
Replaceable Low Profile Hepa Blower
FT2424-LO-AL
2' x 2'
Please Call for Pricing
- Construction of 14 ga, mil finish aluminum using inward turned folded flanges, sealed & fastened from within, providing smooth, airtight plenum
- OD 23 5/8"w x 23 5/8"l x 12 3/4"h
- Motorized impeller type blower with (1) 100w, 110V, 1.0 FLA motor & electronic speed control w/ off setting, developing 360 cfm @ 0.4" SP
- Top mounted 10" duct collar
- These unit fans are sized to push the supply air through the HEPA only, the supply plenum or ductwork must be pressurized by a separate air handler
- Filter is room-side replaceable
- 99.99% seal HEPA filter, anodized aluminum frame, integral white expanded metal face grille
- Unit tabs for hanging, unit weight @ 30 lbs
- Construction of 14 ga, mil finish aluminum using inward turned folded flanges, sealed & fastened from within, providing smooth, airtight plenum
- OD 23 5/8"w x 23 5/8"l x 12 3/4"h
- Motorized impeller type blower with (1) 100w, 110V, 1.0 FLA motor & electronic speed control w/ off setting, developing 360 cfm @ 0.4" SP
- Top mounted 10" duct collar
- These unit fans are sized to push the supply air through the HEPA only, the supply plenum or ductwork must be pressurized by a separate air handler
- Filter is room-side replaceable
- 99.99% seal HEPA filter, anodized aluminum frame, integral white expanded metal face grille
- Unit tabs for hanging, unit weight @ 30 lbs

Replaceable Low Profile Hepa Blower
FT2448-LO-AL
2' x 4'
Please Call for Pricing
Filter Replaceable Terminal housing (Low Profile) - (PRE FILTER)
- Construction of 14 ga, mil finish aluminum using inward turned folded flanges, sealed & fastened from within, providing smooth, airtight plenum
- OD 23 5/8"w x 47 5/8"l x 12 1/2"h
- Motorized impeller type blower with (2) 100W, 110 V, 1.0 FLA motor & electronic speed control w/ off setting, developing 600 CFM @ 0.4" SP
- Top mounted disposable prefilters
- Bottom loading 99.99% gasket seal hepa filter, anodized aluminum frame
- Removable perforated anodized aluminum grille, 1/8" holes on 3/16" staggered centers, allowing for 40% open area
- Unit tabs for hanging, unit weight @ 60 lbs
- Service for motors is from below by removing the filter
Filter Replaceable Terminal housing (Low Profile) - (PRE FILTER)
- Construction of 14 ga, mil finish aluminum using inward turned folded flanges, sealed & fastened from within, providing smooth, airtight plenum
- OD 23 5/8"w x 47 5/8"l x 12 1/2"h
- Motorized impeller type blower with (2) 100W, 110 V, 1.0 FLA motor & electronic speed control w/ off setting, developing 600 CFM @ 0.4" SP
- Top mounted disposable prefilters
- Bottom loading 99.99% gasket seal hepa filter, anodized aluminum frame
- Removable perforated anodized aluminum grille, 1/8" holes on 3/16" staggered centers, allowing for 40% open area
- Unit tabs for hanging, unit weight @ 60 lbs
- Service for motors is from below by removing the filter

Non-Replaceable Low Profile Hepa Blower
FTE2424-LO-AL
2' x 2'
Please Call for Pricing
- Construction of 14 ga, mil finish aluminum using inward turned folded flanges, sealed & fastened from within, providing smooth, airtight plenum
- OD 23 5/8"w x 23 5/8"l x 12 3/4"h
- Motorized impeller type blower with (1) 100w, 110V, 1.0 FLA motor & electronic speed control w/ off setting, developing 360 cfm @ 0.4" SP
- Top mounted 10" duct collar
- These unit fans are sized to push the supply air through the hepa only, the supply plenum or ductwork must be pressurized by a separate air handler
- Filter change by removing motor pack from filter
- 99.99% seal hepa filter, anodized aluminum frame, integral white expanded metal face grille
- Unit tabs for hanging, unit weight @ 30 lbs
- Construction of 14 ga, mil finish aluminum using inward turned folded flanges, sealed & fastened from within, providing smooth, airtight plenum
- OD 23 5/8"w x 23 5/8"l x 12 3/4"h
- Motorized impeller type blower with (1) 100w, 110V, 1.0 FLA motor & electronic speed control w/ off setting, developing 360 cfm @ 0.4" SP
- Top mounted 10" duct collar
- These unit fans are sized to push the supply air through the hepa only, the supply plenum or ductwork must be pressurized by a separate air handler
- Filter change by removing motor pack from filter
- 99.99% seal hepa filter, anodized aluminum frame, integral white expanded metal face grille
- Unit tabs for hanging, unit weight @ 30 lbs

Non-Replaceable Low Profile Hepa Blower
FTE2448-LO-AL
2' x 4'
Please Call for Pricing
- Construction of 14 Ga, mil finish aluminum using inward turned folded flanges, sealed & fastened from within, providing smooth, airtight plenum
- OD 23 5/8"w x 47 5/8"l x 12 1/4"h
- Motorized impeller type blower with (2) 100W, 110V, 1.0 FLA motor, developing 720 CFM @ 0.4" SP
- Top mounted speed control
- Top mounted disposable Prefilters
- Filter change by removing motor pack from filter
- 99.99% HEPA filter, anodized aluminum frame, integral white expanded metal face grille, 2 3/4" separatorless media pack
- Unit tabs for hanging, unit weight @ 50 lbs
- Construction of 14 Ga, mil finish aluminum using inward turned folded flanges, sealed & fastened from within, providing smooth, airtight plenum
- OD 23 5/8"w x 47 5/8"l x 12 1/4"h
- Motorized impeller type blower with (2) 100W, 110V, 1.0 FLA motor, developing 720 CFM @ 0.4" SP
- Top mounted speed control
- Top mounted disposable Prefilters
- Filter change by removing motor pack from filter
- 99.99% HEPA filter, anodized aluminum frame, integral white expanded metal face grille, 2 3/4" separatorless media pack
- Unit tabs for hanging, unit weight @ 50 lbs